Home›Industry News›Pango Replacing XILINX: It Can Be Swapped, But Don't Expect a Drop-In
← Back to Industry News
Industry

Pango Replacing XILINX: It Can Be Swapped, But Don't Expect a Drop-In

IndustryPango ReplacingXILINX: It Can BeSwapped, But Don't…fpga.love
Illustration

In discussions of domestic FPGA alternatives to XILINX, Pango is often treated as the first choice. But a selection review from an actual project shows that the PG2L100H and XC7A100T are close on paper, while what really blocks migration is the transceiver reference clock wiring, reversed differential pair ordering, and PCIe lane order—none of which appear in the parameter tables.

Two series underpin the replacement path

The mainstay for Artix-7 migration is the Logos-2 series. The PG2L100H is often compared with the XC7A100T: roughly 100K equivalent LUT4, with block RAM and DSP counts equal or slightly higher on paper; the PG2L50H is available when resource needs are lower. One tier up is the Titan-2 PG2T390H, built on 28nm with about 390K logic resources, supporting PCIe Gen3 and higher-speed SerDes. Above that, the Titan-3 PG3T1300/1500 uses FinFET process and reaches the billion-gate class, aimed at data centers and high-end communications—not yet needed for ordinary industrial control projects. A product line stretching from CPLDs to the billion-gate class is why Pango is repeatedly mentioned in domestic selection discussions.

Deployments cluster around acquisition and video

Existing cases cluster in industrial control, data acquisition, and image/video. Tronlong's multi-channel AD acquisition solution based on the PG2L100H is used in power online monitoring and distribution network terminals; the PGL50G has been compared with the XC7A35T, with the evaluation concluding it has more abundant resources and larger BRAM, and AD7606/AD7616 reference designs have already been deployed. On the video side, Beige Logic's JPEG XS transmission system based on the PG2T390H is officially stated to achieve end-to-end latency under 100 microseconds at 4K@60fps; an FPGA+AI heterogeneous platform based on the PG2L200H is also used in industrial inspection and smart transportation. What these scenarios share is low sample rates and limited channel counts, where reference designs can directly support productization.

ArchitectureProcessEcosystem
Illustration

Migration cost hides in the physical layer and IP

The HSSTRREF pin of the PG2L100H-FBG484 requires a 200Ω resistor pull-up to +1.0V, while the corresponding Artix-7 pin is pulled up to +1.2V through 100Ω; the CLK, RX, and TX differential pair numbering is reversed relative to XILINX. One project reported that PCIe worked in debug mode but failed on the actual device because the lanes were mirrored, and Logos-2's PCIe IP explicitly does not recommend Lane Reversal in ×1/×2 scenarios. IP core infrastructure is mainly concentrated at the DDR3, PCIe, and basic DSP/memory block level; if the original design relies heavily on Block Design and AXI interconnect, that part carries the largest workload. PDS constraint files use the .sdc suffix, with syntax similar to XDC but different in details; synthesis and place-and-route may be slower than Vivado, with one project reporting an Fmax gap of 10% to 20%.

Three takeaways
  • PG2L100H targets XC7A100T, but the pins are not compatible—swapping parts requires a board redesign
  • Transceiver reference clock and differential pair order are reversed versus XILINX, so the PCB must be redone
  • PCIe Lane Reversal support is limited; routing in XILINX order will most likely fail

What it means for us

For domestic engineers building boards and high-speed interfaces, the chip is usable, but only on the premise that migration is treated as a new design: change the HSSTRREF pull-up resistor network on the schematic first, reorder the differential pairs and lane order on the PCB per Pango's manual, and do not reuse a board laid out for XILINX. On the toolchain side, PDS constraint templates, IP output directories, and simulation include paths need to be manually fixed, and IP dependencies must be confirmed item by item for corresponding replacements. On the supply chain, there is one more optional source, but the cost is a longer high-speed interface debugging cycle—especially for PCIe Gen3 and above or multi-channel SerDes projects, where extra time must be reserved.

domestic FPGAPangohigh-speed interfacesselection and migration
fpga.love